Exactly how to Install a Tub (Step By Step).
Exactly how to Install a Tub (Step By Step).
Blog Article
What are your thoughts concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
![Tools You Need to Install a New Bathtub](https://earlyexperts.net/wp-content/uploads/2017/08/removing-tub.jpg)
Setting up a bath tub isn't exactly brain surgery, yet it does need solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately hard project. If the old bathtub is easily accessible, the task can relocate immediately; if you have to open a wall surface to get rid of the old tub and place the brand-new bathtub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will need an assistant to leave the old tub and also set in the new one. See to it you have qualified on your own for the job and also fit attempting it. As opposed to employing a contractor to take control of a halfway-completed job, it is better to take into consideration employing one prior to you begin. Chances are you might need a specialist plumber to make tube connections.
This article will certainly help you mount a new bath tub in your shower room if you have actually already bought a brand-new tub as well as don't require to change the setup of your previous supply of water pipelines.
Your tools and also material list ought to consist of the following:
Getting ready for the Installation
First of all, the sustaining frame provided with the bath must be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to see to it that if the tap includes a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile tap adapters to the bottom of both taps using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite problematic due to the restricted gain access to that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the bathtub till the level checks out level.
To mount taps, fit the bottom of the outermost versatile tap connector to the ideal supply pipe by making a compression join; after that do the exact same for the other faucet.
Turn on the supply of water and also inspect all joints and brand-new pipework for leakages and tighten them if essential. Fill up the bathtub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, repair the bath paneling as defined in the manufacturer's instruction manual. Tiling and securing around the tub should wait till the tub has been made use of at the very least once as this will certainly resolve it into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in place in between the faucet and the sink. Safeguard the tap in place with the supplier given backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind needs to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the location where the bath meets the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to crack a stiff seal, triggering the water to permeate the wall between the bath and the tiling, resulting in issues with moisture as well as possible leakages to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can break fairly early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
![Tools You Need to Install a New Bathtub](http://ukbathroomguru.com/wp-content/uploads/2015/02/bathroom-installation-supporting-frame-before.jpg)
I'm very involved in Installing A Bathtub and I hope you appreciated the blog entry. Appreciated our post? Please share it. Help another person check it out. We cherish reading our article about How to Install a Bathtub Yourself.
Schedule Now! Report this page